Do You Discover Pipes Complicated? Usage This Advice

Did you know that loose pipes might be responsible for the hammering sounds in your plumbing? If this interests you, you might wish to check out all of the other great information in this article. Take a few minutes and learn all you can learn about plumbing today.

If your pipes bang when you turn on the water, and all the pipes are anchored correctly, you should add some straps or cushion the pipes with a rubber blanket. There may be times when you will need to do both. Make sure that if you have copper pipes, you are not using galvanized straps.

Don't pay a plumber until the job is completed. A plumber may require some money upfront, but it's wise to wait until the job is completely done before giving him the entire payment. Many things can happen between the stop and end of a job, so to be safe wait until you are satisfied with the completed work before paying.

To avoid clogs, pay attention to what you flush. Sanitary napkins, thick toilet paper and baby wipes should never be flushed. These items can expand and cause a clog, or get caught on a pipe. Instead, dispose of them in a sanitary way that does not involve flushing them down the toilet.

Basic problems with toilets can be a quick fix for even the rawest amateur plumber and is worth attempting if you can take the time to research the problem. visit the next document out the necessary part or parts from your local hardware store and ask for support in how to properly install them.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

Find out the plumbing codes in your local area before starting any project. Plumbing codes can vary wildly from area to area and you don't want to run afoul of the codes. Visit your local building department to find out information or hire a plumber for a day to help you go over your plans and provide advice.

Have your pipes in your plumbing system frozen? You can skip the cost of hiring a plumber by using this method. First, open the faucet so steam produced by the thawing process can escape. Begin thawing close to the faucet, and move down the line as each section thaws out. Use a hair dryer or a heat lamp to warm along the pipe. Even though this method consumes quite a bit of time, it is safer than most other heating methods. Furthermore, it requires no cleanup.

To be able to get a good plumber you can be comfortable with, remember which of your friends are actual home owners and not renting. At http://reynalda07loris.tinyblogging.com/Requirement-Plumbing-Help-Use-This-Fantastic-Info--18688599 , every home owner has had to call in a plumber. They can give you a good personal reference they had a positive experience with.

Do you have a frozen drainpipe? You can use a garden hose to thaw it out. First of pop over to this web-site , remove the trap from the drainpipe and insert the hose until it will not go any further. While lifting up the other end of the hose, pour hot water down it. Keep pouring hot water down the hose until the drainpipe thaws. To save time with cleanup, keep a bucket underneath to catch the water that overflows.

When having a consultation about a job with the plumber, take the opportunity to get to know them andtheir business better. Ask about their experience with the type of job that you are wanting to have done. Being comfortable with your contractor is important. They may be spending significant amounts of time in your house depending on the complexity of the job. You want to be convinced that they're up to the task.

Try to limit the amount of hair that goes down your drains. Hair can become tangled up in the pipe and end up blocking up the them, preventing water from flowing smoothly. Buy a cheap screened drain cover to put over your drain to stop any hair from going down and clean it off regularly.

To prevent the most common kitchen sink clogs, avoid putting any sort of solid foods down your drain. Many foods, such as eggs and vegetable and fruit waste actually harden with exposure to cold water and over time can form clogs that are next to impossible to remove without professional help.

Make https://www.necn.com/news/new-england/Efforts-Stepped-Up-to-Restore-Merrimack-Valley-Gas-Service-494033041.html that the temperature of your home's water heater is not above 120F. On older water heaters, be sure it is not above medium settings. When temperatures get higher than 120, scalding can occur. Also, having the settings above 120F, tends to use more energy than lower temperatures do.


Use a foaming root killer, twice yearly, to remove tree roots that can bring your drains to a standstill. Foaming products fill the entire pipe with chemicals, killing roots that grow from the top of the pipe as well as the part that water flows through. They are more effective than regular root killers for this reason.

An important plumbing-related decision that must be made these days is the choice between an electric water heater or a gas water heater. In these times with gas costing as much as it does, it is more cost efficient to buy an electric water heater, especially if you have a smaller water heater.

When looking at new fixtures for your plumbing, look at the option of purchasing ones made of brass. For starters, brass fixtures are much more durable and last longer. In addition, brass fixtures are more aesthetically appealing than fixtures made of other materials. These can be found in any home repair type of store.

To make sure your sump pump will run in an emergency, routinely test it by adding several buckets of water into the sump pit. The pump should turn on, remove the water and turn off with ease. Do this regularly, especially if your sump pump doesn't run that often, to ensure it will work when needed most.

As tempting as it may be to try and save on the heating bill, keep your furnace set no lower than 55 degrees over the winter to prevent inside pipes from freezing. If you have pipes located in an excessively cold basement, consider running a space heater in the basement, but only when it can be checked on frequently.

As you can see, many plumbing problems are very easy to solve on your own if you have the proper knowledge. Don't let a professional plumbing service charge you a hand full for something that you can do on your own! Try the tips in this article next time and see the money you save!

Finding The Right Individual For Your Pipes Needs

Over time, plumbing in our homes is bound to fail. You can call a plumber to fix this, or you can try your hand at doing your own plumbing. Doing your own plumbing jobs is not always easy. The following article will contain helpful advice for anyone who wishes to do their own plumbing.

When concerned with plumbing, you need to know what can cause noisy pipes. This is important because it can mean the difference between an annoying noise and flooding in your house. Do your research to distinguish between the different noises and hire a professional if any serious risk is posed.

When choosing a plumber make sure he is insured and licensed. This is very important. If there is a plumbing emergency, you want to make sure the plumber has met the training requirements of the state. If he is insured, this covers any accidental damage done while fixing your plumbing.

Ensure that everyone in your household knows how to turn off the main water supply, or knows how to contact someone who can. In the event of a burst pipe or other water-related emergency, you should immediately turn off the water to prevent flooding, structural damage, and a sky-high water bill.

If you have a clogged drain, don't use cleaning chemicals to try to clear the clog. These harsh chemicals can corrode your metal pipes leading to leaks and broken pipes over time. Instead, stick to a plunger or make use of a plumbing snake to clear them.

Before you can fix a toilet that does not flush properly, it is important that you find out what is causing the problem. Depending on what the problem is, you may be able to fix it yourself. However, more complicated toilet flushing problems may require the services of a plumber.

Check the floors in your bathroom for any give in order to be sure that there is no damage in the floors. Sit reversed on the toilet (facing the tank) with your feet on the floor. Rock your weight onto each foot in turn and see if you can feel any weakness or "give" in the floor. You could save yourself money but noticing that problem sooner, rather than later.




If water is flooding your home, immediately switch off the main electrical power. If water comes into contact with any electrical components, it can become a fatal situation. Once the power is off, then deal with the flood water. Put your own and your family's personal safety first, and show each member of the family how to shut off the power.

Always keep your garbage disposal clean. You can do this in many ways. Pour some dish soap in and let the disposal run for a few minutes with some cold water. Be sure to run it regularly, if not, it can cause rust. To eliminate foul odors, grind lemon or other citrus peels. You can clean the walls of the disposal by grinding small fruit pits or egg shells.

If your toilet is constantly developing moisture on the outside, you may want to consider turning up the heat in your bathroom. The biggest cause of "sweaty" toilets is cool and moist air. Believe it or not, this moisture could actually cause damage to your toilet, so it is crucial that you fix the problem.

If water is flooding your home, immediately switch off the main electrical power. If water comes into contact with any electrical components, it can become a fatal situation. Once the power is off, then deal with the flood water. Put your own and your family's personal safety first, and show each member of the family how to shut off the power.

If the water is not going into your dishwasher, the first thing you should do is shit off the water under the sink. Chances are that you have some kind of blockage, and keeping the water turned on could actually create a bigger problem. To fix the blockage, you may need to call a plumber.

Make sure that the temperature of your home's water heater is not above 120F. On older water heaters, be sure it is not above medium settings. When temperatures get higher than 120, scalding can occur. Also, having the settings above 120F, tends to use more energy than lower temperatures do.

Governmental regulations sometimes prevent plumbers from actively providing maintenance to copper piping. If you have a calcium buildup in your copper piping, you are going to need to take care of this yourself. You have to get rid of all the water and add vinegar which eats away the calcium buildup out of copper pipes.

Look at your hot water heater and make sure that the temperature is not higher than 120 degrees Fahrenheit. If it is, it could cause you to get burned or it could reduce the unit's energy consumption. If you determine that the temperature is too high, adjust immediately to avoid any of these things from happening.

If your home has copper pipes, they could expand a little when hot water runs through them. When they do, they can rub against the pipe hangers, causing pipe damage. To avoid this, put a tape layer around the pipes and return them to the hangars.

If you are in need of a new bathtub, try to get one that is made of porcelain enamel. https://www.wkbw.com/news/may-heat-wave-tips-to-cut-your-cooling-costs of tubs do require precise and proper care, but their advantage is that they are able to withstand the chemicals that are found in many bathtub cleaning products.

When facing temperatures below freezing in the winter it is important to leave the hot water dripping. This makes sure that the pipes don't freeze over and saves you the expensive repair of fixing and or entirely replacing a broken pipe. https://www.realtor.com/advice/home-improvement/low-flow-toilets-good-or-bad/ of dripping hot water is well worth saving you from that large expense of replacing a broken pipe.

As soon as you notice any water accumulating on the floor by your water heater, turn off the water valves. If you don't, you may discover that what started out as a small leak can quickly turn into a large leak, which will be harder to shut off.


These tips should have given you some much needed insight on where to start and how to begin with your own plumbing jobs at home. These tips were thoughtfully compiled to help the plumbing beginner learn the basics and some other cool techniques that are simple enough to use for everyday maintenance and repair.

Tips And Tricks On Do It Yourself Plumbing

Taking a step into the wondrous and complex land of plumbing for the very first time might feel a bit daunting. However, by keeping the helpful tips listed below in mind, you will soon find yourself plumbing on par with some of the best plumbers in the field and maintaining your own easily.

Routinely check your appliance connections and faucets around the house for any kind of obvious leaks or nearby signs of moisture. Not only do even the smallest leaks lead to a large waste of water and money, they also can lead to damage to your home or even the development of harmful molds.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out visit the up coming post damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide simply click the following internet site of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

The next time you have a clogged drain, avoid the simple solution of dumping drain-clearing chemicals into the pipes. While this method involves the least amount of effort, the chemicals in these liquid cleaners are destructive to your piping. Instead, consider using a little bit of elbow grease with a plunger, snake, or other device designed to clear your clog without chemicals.

Got a leaky pipe? In many cases you can repair this yourself without the expense of a plumber. If a joint is leaking, tighten it with a pipe wrench. If the leak is coming from a damaged section of pipe, you can try repairing with a store-bought patching kit. One method involves applying waterproof tape to the section of pipe where there is leakage. Before applying the tape, make sure the pipe is thoroughly dry. Make sure that the tape covers two to three inches on either side of the breakage in the pipe.

You should drain all of the water out of the tank of your hot water heater at least once every three to six months. Draining all of the water out of the tank helps to prevent sediment build-up at the bottom of the tank. This sediment can cause the tank to bang or to heat less efficiently.

Water from wells can cause orange or rust colored stains in places like bathtubs and sinks. This comes from large amounts of iron present in the water. You can use water softener that you buy at the store to remedy this situation, or you can have a professional do it for you.

Making sure you know all of your problems so you can have them fixed by one plumber visit is very beneficial. Having them all fixed in one visit takes a lot of money off of your bill because you don't have to pay for the visit multiple times so make sure you make a list first.

If your sink is letting rusty water out and it will not drain, it is mostly likely because of the biological scum and grease that is built up in the pipes. You need to have your drains professionally cleaned, allowing maximum flow through your drains. https://www.youtube.com/playlist?list=PLnJ4vmrBHOmuwQu3dtDuVEhCMCi-pYJk2 must be open completely.

Regular maintenance of your plumbing lines is a great idea. Your options are getting your lines snaked or jetted. Jetted is a technology that is proven more effective than snaking is. It gets deeper and cleans harder. So jetting is a good idea next time you are having maintenance performed on your lines.

If you have a crack in your toilet tank, you can sometimes fix this with an epoxy resin. However, it is very difficult to keep up with this type of maintenance, and the best bet may be contacting the supplier and ordering a new tank to be installed in your bathroom. Nevertheless, keeping some epoxy resin on hand for emergencies is a good idea.

If the pipes have burst in an upstairs area, use a tool to perforate the ceiling underneath in several places and places pots and pans under to catch the water. If this is not done, the weight of the accumulating water could cause a collapse of the entire ceiling.

Plumbing should only be done by professionals if there is a major problem or if you do not understand plumbing. Many of the big problems that plumbers deal with, actually have simple solutions. The average person, who does not understand the intricacies of plumbing, usually end up compounding the problem by causing other costly damage to the house during the failed repair. The plumber will need to be called in the end, anyway.

If your water bill seems unusually high and you haven't changed your water usage, the problem is most likely in the service line. The cost to hire a professional to find and repair the service line most often is far greater than installing a new line and then having the old one shut off permanently.

Toilet Installation Plumber prevent plumbers from actively providing maintenance to copper piping. If you have a calcium buildup in your copper piping, you are going to need to take care of this yourself. You have to get rid of all the water and add vinegar which eats away the calcium buildup out of copper pipes.

Clean washing machine lint traps and use pantyhose over the water outlet tube to prevent lint, fuzz and other debris from clogging sewer or septic system filters. Fine mesh traps are also available for this purpose, but a package of knee-high nylon stockings and plastic ties can provide enough filters to encourage you to do the job regularly.


Never try to undertake a project that you are unsure of. Additionally, never call on a friend to help you with something, if they are not a professoinal. There have been hundreds of good friendships ruined by a guy claiming to know exactly what he is doing, when the truth is he is clueless.

Are you looking for a simple tip to determine if your toilet has a hidden leak? Here is one that is not only simple, it also will not make a big dent in your wallet. Simply add six drops of food coloring into the toilet tank. If your toilet is leaking, color will appear in the bowl within 30 minutes.

You can save money on a plumber by using a power auger yourself to clear a clogged toilet line. Check with local home improvement stores or other venues where you can rent power tools. You may be able to rent an auger yourself for a fraction of the cost of hiring a plumber, although you will have to be able to remove and reset your toilet yourself if you do not have a main line cleanout.

Hopefully, these tips have provided you with some very valuable information, as well as given you a way to organize all of the thoughts and information you may have already had on plumbing. Keeping these tips in mind when you start plumbing can help you to become a very good plumber.

Discover The Very Best Plumbing Technician For Your Requirements

Were you aware that water pressure above 80 psi can actually cause a loud hammering sound to occur in your plumbing system? This can be easily resolved by installing a valve that can adjust the incoming water pressure. For more great expert tips, check out the rest of this article.

If you have noisy pipes, you can cushion them with a rubber blanket or add additional anchor straps. Banging pipes are usually caused by loose pipes, water hammering to a stop as you turn it off, or hot water pipes shifting in their position. All of these problems can be solved by cushioning and anchoring the pipes.

Roots from a tree in your back yard can be a real headache when it comes to plumbing. Make sure if you have a big tree or bush or some kind of plant with a big root system, that you ask your plumbing company about root killing agents. Water Heater Repairman Near Me can flush these down your toilet and kill any roots that may be blocking your pipes and save yourself a lot of money by stopping a back up before it happens.

If you have noisy pipes, you can cushion them with a rubber blanket or add additional anchor straps. Banging pipes are usually caused by loose pipes, water hammering to a stop as you turn it off, or hot water pipes shifting in their position. All of these problems can be solved by cushioning and anchoring the pipes.

You need to winter-proof your house. You have to make sure you switch of the master circuit breaker or the shut-off valve before you leave your house. Since one small hole or congested water can quickly freeze and cause pipes to break and expand, you need to drain and open all outdoor and household water lines.

Be careful about using liquid clog cleaners. These liquids can contain chemicals that are extremely bad for your pipes. Instead, use a snake or a plunger to dislodge any clogs you might encounter. Be sure to try these things before giving up and calling a plumber, who will probably re-perform those same acts.

To avoid freezing pipes in the winter, make sure to insulate any exposed pipes in you basement before winter comes. Pay extra attention to pipes near the outside walls. If you have had a problem with any particular pipe freezing in the past, apply some heat tape to insulate those pipes.

Before the cold season hits, check out the condition of your gutters on the roof of your house. Remove all debris, leaves and branches so that you can have a smooth flow of water and easy drainage. Caretaking in advance will help to prevent serious issues with plumbing down the road.

Do you have a frozen drainpipe? You can use a garden hose to thaw it out. First of all, remove the trap from the drainpipe and insert the hose until it will not go any further. While lifting up the other end of the hose, pour hot water down it. Keep pouring hot water down the hose until the drainpipe thaws. To save time with cleanup, keep a bucket underneath to catch the water that overflows.


If the hot water heater in your house is over ten years old, you should look at replacing it. Hot water heaters are very susceptible to corrosion on the bottom. This can lead to leaking and flooding whatever room it is in. Then not only will you have to replace it, but you'll have to fix any damage caused by the leak.

The key to finding a great plumber for new construction is to look at their prior jobs. Good plumbers take pride in the work they do, so they will have photos and references from previous jobs. If the plumber you are considering hiring does not have references or photos of previous jobs, then stay away and find another.

During the warm seasons, you will see that there will be many bird nests forming in and around your plumbing vent pipes. It is essential to clear these out, as they can have a devastating effect on the quality of your plumbing and the flow of water in your home.

To make sure your sump pump will run in an emergency, routinely test it by adding several buckets of water into the sump pit. relevant resource site should turn on, remove the water and turn off with ease. Do this regularly, especially if your sump pump doesn't run that often, to ensure it will work when needed most.

If the water pressure on your street exceeds 60 pounds, you many want to consider installing a pressure reducing valve. Too much water pressure is actually harmful to your plumbing system and could cause excess water pressure. A pressure reducing valve cuts down your water pressure by almost 50 percent.

If you have an automatic sprinkler system, you want to consider getting a spring-loaded timer which can be attached directly to your hose. This prevents your lawn from getting too much water in case you forget to turn your system off. Getting too much water could kill your grass and plants.

To avoid Sewer Drain Camera from accumulating and clogging pipes. Use fine mesh strainers in every drain where hair is washed. Fine mesh strainers can catch the hair and still allow the shower, tub or sink to drain and are also useful in the kitchen to catch and stop small food debris from going down the drain.

Keep a grease vat in your kitchen to pour all used cooking grease into. Grease is a big reason that kitchen drains slow and eventually, stop up. Even the harshest drain cleaning products, tend to not be a match for a heavy grease clog. The grease you save in the vat can be formed into balls and rolled in bird seed for wonderful winter bird feeders.

It is imperative as a homeowner that you know exactly where your main water shut-off valve is located and can operate the valve in case of an emergency. The best first step measure for frozen pipes is to stop water from entering your home in the first place. Locate the main water supply valve and turn it on and off on a regular basis to keep it easily operable in an emergency.

Avoid over-tightening water faucet handles. Use only enough pressure to stop the water from flowing and dripping from the faucet. Anything else is overkill and will quickly wear out the gaskets and washers inside those handles and cause leaking or the inability to stop the water from coming out of the faucet.

When Web Site have a plumbing problem that comes up in your home, you do not necessarily have to pay a plumber a lot of money to come out and fix it for you. The helpful points you learned in this article will enable you to care for basic plumbing maintenance and repairs around your home yourself.

Looking For Great Guidance About Pipes? Have A Look At These Valuable Solutions!

If plumbing is something that you find difficult or intimidating, you are not alone. Many people can't solve their own plumbing problems, which means that plumbers can charge a lot of money for even simple and quick repairs. Don't let this happen to you, read on to learn how to solve your own plumbing problems!

To prevent the pipes from freezing, it is advisable to seal off air vents, cracks and access doors. In order to keep the heat in and the cold out, you can try using insulation or caulk. In the event a leak occurs, make it a point to remind everyone where the master circuit breaker is so it can be shut off immediately.

Check your gas water heater periodically to make sure the pilot flame is lit. The correct color for this flame should be blue. The tip of the flame should be yellow. If you find that you are only seeing a yellow flame, you may need to call a professional for safety reasons.

Group all of your plumbing repairs before scheduling a plumber to come out. Check all of your fixtures and faucets. If anything is dripping, running or clogged, make a list for the plumber. That way, when the plumber comes, they can do all of the jobs in one visit. This will cut down on charges.

Taking preemptive action to fix a strange smelling kitchen sink can be a good way to keep your kitchen smelling great. Make sure not to throw hair or grease into your sink. Use baking soda if you have a strange smell coming from your drain. Make sure you use your garbage disposal if you have one to grind up any food and use water while doing this to prevent damage to the blades of the garbage disposal.

Watch how your toilets are flushing. If you have to jiggle the handle or if it takes too long, you might have to repair some toilet parts. Replacing see this site may help you to save on your water bills and will save you from more expensive repairs at a later date.

If you are using PEX tubing for the supply lines in your home, make sure you get the right tools for the job. PEX tubing requires a completely different tool type than regular lines. PEX has a lot of benefits though, so don't let the different requirements throw you off.

One of the things that you can do to safeguard your home from any serious plumbing issues is to install a flood alarm. This is a device that will sound when it comes in contact with water, alerting you if there are any issues in a particular area in the house.

Avoid pouring grease or oil down your kitchen sink drain. Grease and oil can build up in your pipes and cause a backup. Instead, wait for the grease or oil to cool and solidify and either throw it away or see if there's a place to recycle it near your home.

Insulate your pipes properly. If the temperature drops below fifty five degrees, your pipes could freeze. This makes pipes extremely fragile and increases the risk of leaks and damages. The pipes inside your house should not freeze but take a look at a plan of your plumbing system to see if you have any pipes outside of your house.


During the winter months, your water heater works the hardest. To keep it in optimum condition, flush it out before winter arrives. Flushing the system helps remove the sediment buildup, which causes internal corrosion of your water heater, shortens its lifespan, and reduces heating efficiency. Connect a hose to the faucet near the bottom of the tank and drain several gallons by directing the water into a nearby drain.

The most important plumbing tip you need to know is -- how to turn off your home's main water supply. Once the water is shut off, you can investigate problems and figure out how to resolve them. Walk https://www.express.co.uk/life-style/life/877976/frozen-pipes-tap-plumbing-winter-thawing through the house and show them where all the water shut-off valves are, and how to use them.

A great way to save a few dollars is to add insulation to your hot water heater. Much of the energy required to heat the water in your home is the expense from keeping the water in the tank hot for when it is needed. Adding an extra layer of insulation can help reduce this cost.

Check for standing water in your yard which can be a direct result of leaking pipes. Standing water can cause an increased level of damage to your lawn and will attract bacteria and insects. Reduce your level of standing water to put your family and home in the most secure position.

If you need to get a new toilet, be sure you go with a trustworthy brand. Cheap toilets are more likely to break down easily and you will end up having to buy a new one. If you are unsure of which brands are good, ask the salesperson in a home improvement store.

To avoid water damage to walls in the kitchen, make sure all seams in your counter tops and back splash are properly sealed using a waterproof silicone. visit my home page will dry out over time, crack and shrink and should be replaced once every three years. Keeping your silicone in good shape will keep kitchen spills where they belong and not running down the walls.

If you hear loud, vibrating noises coming from your pipes, you may want to consider adding air chambers to the end of the pipes and tightening them. Usually, these noises are caused from opening and closing faucets too quickly and tightening the pipes and adding air chambers can fix this problem.

If you see any water pooling near your hot water heater, shut the water off to the heater immediately. If Suggested Online site don't, a small leak can turn into a much larger leak, making it harder to shut off.

Before your plumber begins work in your home, make sure you receive a detailed estimate detailing the work to be done, parts needed, a time line and projected completion date. Having all of this information beforehand will give you an idea of what the costs are going to be and how long everything should take.

With a little bit of plumbing, you can route water anywhere you want in your home. Doing so, makes it possible to live anywhere and adds convenience to any room - but done wrong can mean a financial disaster! Keep the wisdom of this article in mind and you can keep the water flowing where you want but in ways you can handle.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15